CSIRO Publishing Home Books Journals About Us Contact Us     Follow PrometheusWiki on Twitter
Prometheus Wiki
Loading...
 

ProtocolProtocol

(Cached)

Plant flammability

Admin26202 points 
Contributors : Perez-Harguindeguy, N.243 points 


Protocols that receive sufficient votes and a high star rating will be considered for Gold Leaf Status by the PrometheusWiki Editorial Board.



Author Affliations

This article is modified from Pérez Harguindeguy et al. (2013). The "New handbook for standardised measurement of plant functional traits worldwide" is a product of and is hosted by Nucleo Diversus (with additional Spanish translation). For more on this trait and on its context as part of the entire trait handbook visit its primary site Nucleo DiverSus at http://www.nucleodiversus.org/?lang=en

Overview

Flammability-enhancing traits are important contributors to fire regimes in (periodically) dry regions and therefore they have important ecological impacts (particularly on ecosystem dynamics), as well as socioeconomic and climatic consequences. The intrinsic flammability of a plant depends on both its traits while alive and the effects of its leaves, branches, and stems after those organs’ deaths. The flammability of those organs (either living or dead) depends on (1) the type or quality of the tissue, and (2) the architecture and structure of the plant and its organs (which is mainly related to heat conductivity).

Note that the flammability of a given species can be overridden by the flammability of the entire plant community (e.g. amount of litter, community structure and continuity, organic matter content of the soil) and by the particular climatic conditions (e.g. after a long very dry period, many plants would burn quite independently of their flammability).

Flammability (broadly defined as the propensity to burn) is a compound plant functional trait. Its components vary among authors and disciplines. Most studies are based on flammability measurements of small plant fragments in chambers in the laboratory. Although this produces highly standardised results, it does not scale up well to whole-shoot flammability. We propose a standard method for measuring flammability in which the basic architectural arrangement of the measured shoots is preserved (see More on methods in the reference section, and Fig. 1 for illustration) This involves a low-tech device in which shoots up to 70 cm long are placed, preheated and ignited in a standard way, then the following measurements are taken:

(1) maximum temperature reached during burning (in °C, MT), measured with an infrared thermometer from a distance of 50 cm to the burning shoot;

(2) burning rate (BR), a value obtained by dividing the length of the sample that was burnt by the burning time (in seconds); it gives an idea of how quickly flames can spread across the plant and to what extent the plant is able to carry fire; and

(3) burnt biomass percentage (BB), consisting of a visual estimation of the burnt biomass (percentage intervals); the intervals are 1 = <1%, 2 = 1–10%, 3 = 11–25%, 4 = 26–50%, 5 = 51–75% and 6 = 76–100%.

 

Fig. 1. General view of a device for measuring plant flammability in the field (reproduced with permission from Jaureguiberry et al. 2011). (a) Grill, (b) grill thermometer, (c) temperature gauge, (d) security valve, (e) connection to gas cylinder, (f) removable legs, (g) blowtorch valve, (h) blowtorch, (i) burners, (j) ventilation holes, (k) barrel, (l) removable wind protection and (m) gas cylinder. See text for technical details. 

Materials/Equipment

 

Units, terms, definitions

 

Procedure 

For calculating (overall) flammability, the scores on each component must be transformed to a proportional scale, with the value 1 being assigned to a reference value. In the case of BB, the value 1 was assigned to the maximum possible value for this component (i.e. 6), whereas for the other components, the reference value was based on the literature and the results of our experiments. Reference values are: MT=500°C; BR = 1 cm–1Standardised MT, BR and BB scores are then added to obtain a compound value of flammability (rounded to two decimals) that could vary between 0 (no flammability) and ~3 (maximum flammability).

As an alternative to the direct measurement of flammability, an estimation may be obtained by measuring several plant attributes that are known to influence plant flammability. Five classes are defined for each of the attributes described below (stem and twig water content, canopy architecture, surface : volume ratios, standing litter, volatile oils, waxes and resins). Flammability is subsequently calculated as the average (rounded to one decimal) of the class scores for each of the following individual attributes (see Table 1 for ranges of values of each attribute within each class). We strongly recommend testing and calibrating this estimation against direct measurements of flammability as described above, or against direct measurements of ignitability and combustibility as described under Notes and troubleshooting tips below.

(1) Water content of branches, twigs and leaves. Flammability is expected to be greater in species with higher leaf dry-matter content (see Leaf Dry Matter Content for protocol) and higher twig dry-matter content and it is probably also a function of drying rate (here, represented inversely by drying time from saturation to dry equilibrium).

(2) Canopy architecture. Plants with complex architecture, i.e. extensive branching, tend to spread fire easily. The degree (number of orders) of ramification (branching) is used here as a close predictor of canopy architectural complexity, and ranges from zero (no branches) to 5 (four or more orders of ramification) (see Branching architecture).

(3) Surface-to-volume ratios. Smaller twigs (i.e. twigs of smaller cross-sectional area) and smaller leaves should have a higher surface-to-volume ratio (and, thus, faster drying rate) and therefore be more flammable. Since twig and leaf size tend to be correlated in interspecific comparisons, according to allometric rules, we use leaf size here to represent both traits. A complication is that some species are leafless during the dry season; however, leaf litter is likely to still be around in the community and affect flammability during the dry season (see Comparing leaf area across species). However, for ground fires, substantial accumulation of litter of small leaves may pack densely, obstructing oxygen flow and actually strongly inhibiting fire to spread.

(4) Standing litter. The relative amount of fine dead plant material (branches, leaves, inflorescences, bark) still attached to the plant during the dry season is critical, since litter tends to have very low water content and thus enhance plant flammability. ‘Fine’ litter means litter with diameter or thickness less than 6 mm. We define five subjective classes from no ‘fine standing litter’, via ‘substantial fine standing litter’ to ‘the entire above-ground shoot died back as one standing litter unit’.

(5) Volatile oils, waxes and resins in various plant parts contribute to flammability. This is a subjective, categorical trait ranging from ‘none’ to ‘very high concentrations’. Check for aromatic (or strong, unpleasant) smells as well as sticky substances that are released on rubbing, breaking or cutting various plant parts. Scented flowers or fruits are not diagnostic for this trait.

 

Table 1. Plant flammability traits. Classes for component traits for estimating plant flammability. Flammability itself is calculated as the average class value (rounded to 1 decimal) over all component traits. Flammability increases from 1 to 5 For this calculation, twig drying time (which is probably closely negatively linked with twig dry-matter content) is optional.

 
  Flammability Class
Component trait 1 2 3 4 5
Twig dry-matter content (mg g–1) <200 200-400 400-600 600-800 >800
Twig drying time (day) ³5 4 3 1 £1
Leaf dry-matter content (mg g–1) <150 mg 150–300 300-500 500-700 >700
Degree of ramification (branching) (number of ramification orders) No branches Only 1st-order ramification 2 orders of ramification 3 orders of ramification ³4 orders of ramification
Leaf size (lamina area) (mm2) >25 000 2500–25 000 250–2500 25–250 <25
Standing fine litter in driest season None as one litter unit Some  Substantial (with dead leaves or twigs or flaking bark) More dead than live fine mass above ground Shoot dies back entirely, standing as one litter unit
Volatile oils, waxes and/or resins None Some Substantial  Abundant Very abundant

 

 

Other resources

 

Notes and troubleshooting tips

(1) Ignitability indicates how easily a plant ignites (i.e. starts to produce a flame). It can be measured directly by measuring the time required for a plant part to produce a flame when exposed to a given heat source located at a given distance. Ignitability experiments are usually performed several times (e.g. 50), and the different fuels are ranked by taking into account both the proportion of successful ignitions (ignition frequency) and the time required to produce flames (ignition delay). Tissues producing flames quickly in most of the trials are ranked as extremely ignitable, whereas tissues that rarely produce flames and/or take a long time to produce them are considered of very low ignitability. These experiments are run in the laboratory under controlled conditions (moisture and temperature) by locating a heat source (e.g. electric radiator, epiradiator, open flame) at a given distance (few centimetres) from the sample. The values used to rank species according to ignitability depend on the type and power of the heat source, on the distance of the heat source to the sample, on the shape and size of the samples and on the relative humidity of the environment in the days before the test; these experimental conditions should be kept constant for all trials and samples. We propose using an open flame at 420°C, placing the plant material at 4 cm from the flame. A standard quantity of 1 g of fresh material is being used.

(2) Plant tissue heat conductivity (combustibility) can be assessed by the heat content (calorific value, kJ g–1), which is a comprehensive measure of the potential thermal energy that can be released during the burning of the fuel. It is measured with an adiabatic bomb calorimeter using fuel pellets of ~1 g, and the relative humidity of the environment in the days before the test should be standardised as well. Evidence shows that heat content varies relatively little among species and is only a modest contributor to interspecific variation in flammability.

(3) Combustibility and structural variables. In relation to the surface area-to-volume ratio, other structural variables have been used to characterise the combustibility, especially the proportion of biomass of different fuel classes (size distribution). Typically, the fuel classes used are the biomass fractions of (1) foliage, (2) live fine woody fuel (<6-mm diameter; sometimes subdivided in <2.5 and 2.5–6 mm), (3) dead fine woody fuel (<6 mm), and (4) coarse woody fuel (6–25, 26–75, >75 mm). The summed proportion of live and dead fine fuels (foliage and woody of <6 mm) may be the best correlate of overall surface area-to-volume ratio.

(4) Fuel bulk density (= fuel weight/fuel volume) and canopy compactness (ratio of fuel volume to canopy volume) have also been used to characterise heat conductivity, mainly at the population and community levels. Furthermore, high litter fall and low decomposition rate will increase the combustibility of the community.

 

Links to resources and suppliers

 

Literature references


References on theory,significance and large datasets:

Bond WJ, Midgley JJ (1995) Kill thy neighbour: an individualistic argument for the evolution of flammability. Oikos 73, 79–85. doi: 10.2307/3545728

Bond WJ, Van Wilgen BW (1996) Fire and plants. Chapman and Hall: London.

Cornwell WK, Cornelissen JHC, Allison SD, Bauhus J, Eggleton P, Preston CM, Scarff F, Weedon JT, Wirth C, Zanne AE (2009) Plant traits and wood fates across the globe: rotted, burned, or consumed? Global Change Biology 15, 2431–2449. doi:10.1111/j.1365-2486.2009.01916.x

 Gill AM, Zylstra P (2005) Flammability of Australian forests. Australian Forestry 68, 88–94.

Mutch RW (1970) Wildland fires and ecosystems – A hypothesis. Ecology 51, 1046–1051. doi:10.2307/1933631

Pausas JG, Alessio GA, Moreira B, Corcobado G (2012) Fires enhance flammability in Ulex parviflorus. New Phytologist 193, 18–23. doi:10.1111/j.1469-8137.2011.03945.x

Rothermel RC (1972) A mathematical model for predicting fire spread in wildland fuels. USDAForest Service Research Paper INT. USDA Forest Service: Washington, DC.

Scarff FR, Westoby M (2006) Leaf litter flammability in some semi-arid Australian woodlands. Functional Ecology 20, 745–752. doi:10.1111/j.1365-2435.2006.01174.x

Schwilk DW, Ackerly DD (2001) Flammability and serotiny as strategies: correlated evolution in pines. Oikos 94, 326–336. doi:10.1034/j.1600-0706.2001.940213.x

More on methods:  

Dimitrakopoulos AP, Panov PI (2001) Pyric properties of some dominant Mediterranean vegetation species. International Journal of Wildland Fire 10, 23–27. doi:10.1071/WF01003

Etlinger MG, Beall FC (2004) Development of a laboratory protocol for fire performance of landscape plants. International Journal of Wildland Fire 13, 479–488. doi:10.1071/WF04039

Papió C, Trabaud L (1990) Structural characteristics of fuel components of five Mediterraean shrubs. Forest Ecology and Management 35, 249–259. doi:10.1016/0378-1127(90)90006-W

Scarff FR, Westoby M (2006) Leaf litter flammability in some semi-arid Australian woodlands. Functional Ecology 20, 745–752. doi:10.1111/j.1365-2435.2006.01174.x

Stephens SL, Gordon DA, Martin RE (1994) Combustibility of selected domestic vegetation subjected to desiccation. In ‘12th conference on fire and forest meteorology’, Jekyll Island, GA. Available from:     http://www.cnr.berkeley.edu/stephens-lab/Publications/Stephensetal_93_ Comb_Veg.pdf     Verified 22 February 2013.

Valette J-C (1997) In flammabilities of Mediterranean species. In ‘Forest fire risk and management. EUR 16719 EN. (Ed. P Balabanis, F Eftichidis, R Fantechi) pp. 51–64. European Commission, Environment and Quality of Life: Brussels

Van Altena C, Van Logtestijn RSP, Cornwell WK, Cornelissen JHC (2012) Species composition and fire: non-additive mixture effects on ground fuel flammability. Frontiers in Plant Science 3, 63. doi:10.3389/fpls.2012.00063 

for flammability of whole shoots described above, see:

Jaureguiberry P, Bertone GA, Díaz S (2011) Device for the standard measurement of shoot flammability in the field. Austral Ecology 36, 821–829. doi:10.1111/j.1442-9993.2010.02222.x

 

Health, safety & hazardous waste disposal considerations

 


Contributors to this page: Admin26202 points  and Perez-Harguindeguy, N.243 points  .
Page last modified on Tuesday 29 of July, 2014 15:45:08 EST by Admin26202 points . (Version 15)